search

Incra Build-It Starter Kit Manual de usuario Pagina 6

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 6
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 5
Similar to Plan #001 (Adjustable Angle Crosscut with Drop Panel), this crosscut jig has a shorter 18” fence and uses fewer components
to achieve comparable functionality. The T-Track Plus and user made stop positioner provide repeatable crosscut length control.
The rear mounted T-Track Regular combined with a pair of Build-It Brackets and the twin T-Slot Panel Connectors allow for
unlimited adjustment of the fence angle.
Begin by adding a Miter Slider to a small Build-It Panel. Place in your table saw’s miter slot and adjust for a good fit, then add
a T-Slot Panel Connector to each edge. Increase the platform width to cross the line of cut by adding the large Build-It Panel.
Trim to the blade as described in Steps 3 & 4 shown on the reverse side of your Build-It Panel’s wrapper then mount the cutoff
from the large panel to the opposite
side of the small panel. Make the 18”
fence and stop positioner as shown in
Fig. 3 and Detail 3A using 18” T-Track
Regular and T-Track Plus components
then attach to the T-Slot Panel Connec-
tors using a pair of Built-It Brackets. Now
you can adjust the fence to the desired
angle, clamp your workpiece in place
and begin your project’s crosscut re-
quirements with confidence.
Adjustable Angle Crosscut
Fig.1 Fig.2
Fig.3
Build-It Platform Components Required:
• 1 Large Build-It Panel • 1 Small Build-It Panel
• 1 Miter Slider • 2 T-Slot Panel Connectors
• 18” T-Track Regular
• 18” T-Track Plus
Just add:
w w w.incra.com rev. 10.12.07 ©2007 by Taylor Design Group. All rights reser ved.
System
it
®
Large Build-It Panel
(trimmed to blade)
Attach cutoff from
Large Build-It Panel to opposite
side of Small Panel
18” T-Track Regular
18” T-Track Plus
Plan # 007
Detail 3A
5
/16” dia holes
2
1
/16”
3
/4”
2”
1
1
/8”
3
1
/2”
2
3
/16”
3
/4”
1
3
/4”
1
1
/4”
5
/8”
3
/4” wide
x
1
/2” deep
groove for
T-Track
3
/4”
1
/
4-20 x 1” hex bolt (4)
1
/
4-20 x
1
1
/
2” hex
bolt
Small Panel
Available online at w w w.i n c ra . co m
• Build-It Brackets
• Build-It Clamp
• Build-It Knobs
Vista de pagina 5
1 2 3 4 5 6

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Herramientas Incra Build-It Starter Kit
Herramientas Incra Build-It Starter Kit Manual de usuario   (6 paginas)
Herramientas Incra Build-It STS Mortiser Manual de usuario   (12 paginas)
Herramientas Incra Build-It Panel Manual de usuario   (4 paginas)
Herramientas Incra Build-It STS Slot Mortiser Manual de usuario   (5 paginas)
Herramientas Incra T-Track Single Track Manual de usuario   (1 paginas)
Herramientas Incra Track & Shop Stop Manual de usuario   (8 paginas)
Herramientas Incra T-Track Plus w/Scale Manual de usuario   (1 paginas)
Herramientas Incra HingeCrafter Manual de usuario   (8 paginas)
Herramientas Incra Miter Channel Glue Down Manual de usuario   (1 paginas)
Herramientas Incra Miter Slider SE Manual de usuario   (1 paginas)
Herramientas Incra Miter Slider Manual de usuario   (8 paginas)
  • Retroactive Yeti Cycles Slick Focus-foodservice Menvier Security
  • Shure Altavoces barra de sonido Philips Proyectores IBM Terminales Punto De Venta Manhattan Adaptadores De Interfaz / Cable De Género MTX Altavoces
  • Canon W2200 Samsung HM3100 Metabo PK 300 Spypoint BF-6 Electrolux EW6S4R04W
  • Bork B600 Manual de usuario Electrolux EW7F2912SP Manual de usuario Fujitsu fi-60F Manual de usuario Shindaiwa SV212 Manual de usuario Aeg-Electrolux KM9800E-M Manual de usuario